Modern decoration work, such as home water and electricity installation, will have many lines. In the early days when water and electricity lines were installed, they were all exposed lines, which were simple and convenient to operate, but the aesthetics were poor. With the development of modern society, people are pursuing more and more beauty, so modern decoration basically uses hidden lines. But concealed wiring also has its disadvantages, that is, the wires are very difficult to thread, which makes many electricians complain.

The old-fashioned method before was to put the slender steel wire rope into the line pipe and bury it together when burying the pipe, and then expose it at both ends of the line pipe and make an elbow. However, with the development of technology, some tools in decoration are constantly being updated, so smart masters no longer use steel wire ropes, but use fiberglass threaders, which can thread the thread quickly without getting stuck.

Benefits of Fiberglass Duct Rodder:

The fiberglass duct rodder is an excellent auxiliary tool for pulling guide ropes in pipelines. The smooth and elastic surface allows the rodder to easily pass through narrow channels. The duct rodder consists of three parts: copper core, glass fiber reinforcement layer, and high-pressure low-density polyethylene protective layer (smooth, strong, and resistant to harsh environments). The copper core conductors allow the prongs to be easily positioned in different ways.

At first, fiberglass duct rodders were mainly used for traction under walls, and later developed into traction for optical cables in sewers and other lines. The rodding device has the advantages of saving time, saving labor, and improving work efficiency. It can be used for cleaning telecommunications pipes and laying out optical cables, electrical cables, and plastic sub-tubes. When using it, first pull out the fiberglass-covered rod from the pulley, and then connect it with the corresponding metal head. Penetrate into the pipeline. When used for cleaning, the guide head drives the cleaning tool to clean the pipeline. When laying cables, the steel wire or iron wire can be brought in first, and then the steel wire or iron wire can be used to pull the cable into the pipe. The overall operation is simple and convenient!

These are our hot selling products:

Duct Rodder with Wheels

Fiberglass Duct Rodder

Duct Rodder

The correct way to use fiberglass duct rodder:

1. Be sure to protect the pulling head (one end of the fiberglass piercer, usually copper-plated, with threads on the upper end, which can be loosened and tightened) from being broken. When using the fiberglass duct rodderr, you must first align the traction head with the movable pulley on the small frame, pass it through the pulley, and then perform threading, pulling, and clearing the pipe. If you need to pull all the threaders out of the frame, you should pay special attention to the fact that one end is stuck in the ring on the small frame. This ring is used to fix the pulling head when winding the puncher, so later be careful to break the traction head when pulling it out, and clamp the traction head in the middle of the ring when coiling the punch.

2. The fiberglass perforator is a hard and brittle material, so its bending diameter should be kept at least 60 centimeters during use. In pipelines or other construction environments, if the angle of the pipeline is at right angles or less than 90 degrees, Special attention should be paid to protecting the traction head from being broken, and certain measures should be taken to prevent damage to the threader when pulling out of the shaft.

3. The tolerable temperature range of the fiberglass piercer is between -40 and +80 degrees. Any improper behavior should be avoided during construction, such as contact with overly cold or overheated objects or environments. The product should be placed in a cool place after use. , avoid prolonged exposure to sunlight and rain.

4. The linear traction force of the fiberglass puncher is 2.5 tons. Do not use high-power machinery for traction in a 90-degree right angle environment, otherwise it may break. Never let vehicles or other heavy objects roll over it, otherwise its service life will be greatly shortened.

5. When using a perforator in large-scale cable construction, you cannot use the perforator to directly pull the cable. Use the metal pulling head of the perforator to first pull a steel wire rope in the pipe, and then use the steel wire rope to pull the cable. In this way, the life of the perforator will be greatly improved. , it is recommended to use various pay-off pulleys to improve work efficiency and protect the needle threader.